Gutter pulling away from the fascia
We check the fascia for rot, replace damaged sections, and re-hang the gutter on hidden hangers at regular centres. A gutter screwed back into rotted fascia will pull away again.
Houston averages about 51.8 inches of rain a year, and most of it arrives in hard, fast downpours — so gutters are not trim, they are part of the roof system. Undersized or clogged gutters overflow, back water under the first row of shingles, rot fascia and dump water at the foundation. We install seamless gutters, repair leaking sections and fit downspouts that actually carry water away from the house. Call (346) 654-5170 and we will measure your roofline and quote the runs and downspouts in writing.

A gutter job starts at the roofline: we measure every run, check the fascia and drip edge, and size the gutter and downspouts to the roof area they have to drain. Seamless gutters are formed on site in one continuous run, so there are no joints along the length to leak — only at corners and end caps, which we seal. Hangers go on at regular centres, downspouts are placed where water can actually leave the property, and the whole system is water-tested before we leave.
Gutter repair is part of the same service, not a separate visit: we re-hang gutters pulling away from the fascia, re-seal leaking seams on old sectional gutter, replace crushed or split downspouts, and clear blockages that make a sound gutter overflow. Downspout installation is the other half of the job — a downspout that dumps water at the foundation trades a roof problem for a foundation problem, so we extend discharge away from the house and, where the grade allows, away from walkways. The City of Houston does not require a permit for gutter installation or replacement unless structural changes to the roof are made. Houston's rain does the rest of the argument: a 5-inch gutter on a large, steep roof plane will overflow in a Gulf downpour, which is why we size up to 6-inch gutters and add downspouts where the roof area demands it.
A complete gutter installation covers the runs, the hangers, the downspouts and the discharge. Anything beyond this list is quoted in writing before work starts.
Gutters are formed on site in one continuous run per side, so there are no joints along the length to leak. Corners and end caps are sealed by hand.
Hidden hangers are set at regular centres so the gutter holds its line under a full load of water. Sagging gutters are usually a hanger problem, not a gutter problem.
Downspouts are sized and placed to the roof area they serve, and discharge is directed away from the foundation. A downspout that dumps water at the slab trades a roof problem for a foundation problem.
Corners, end caps and outlets are sealed properly. Leaking seams on old sectional gutter are the most common repair we do, and the reason seamless is the standard for new work.
We check the fascia the gutter hangs from and the drip edge above it. A gutter hung on rotted fascia will pull away, and a missing drip edge lets water run behind the gutter.
Old gutter and downspouts are hauled away, the yard is cleared, and the system is water-tested before we leave.
We measure every run, count the roof area each downspout must serve, and check the fascia and drip edge. You get a written scope for the runs and downspouts before work starts.
We confirm the gutter size — 5-inch or 6-inch — and the material with you, and explain the trade-offs honestly. No brand is claimed as installed unless it actually is.
Old gutter comes down, and the fascia underneath is checked. Rotted fascia is flagged and quoted before new gutter goes up.
Gutters are formed on site, hung on hidden hangers at regular centres, and set to fall correctly toward the downspouts. Downspouts are fitted and secured.
Joints and end caps are sealed, the system is water-tested, and we walk the roofline with you. If anything looks off after the job, call us and we will come back and look.
Gutter work is measuring, forming and levelling. The right tools matter — but the fall toward the downspout matters more.
Forms gutters on site in one continuous run, so there are no joints along the length to leak.
Checks fascia and the roof edge for rot before new gutter goes up. A gutter hung on rotted fascia will pull away.
Set the fall of each run toward the downspouts. A gutter with no fall holds water; a gutter with too much fall looks wrong from the street.
Keep the crew safe on two-storey rooflines. Fall protection is standard on every job.
Apply sealant cleanly at corners, end caps and outlets, where a neat bead decides whether the joint holds.
Set hidden hangers with consistent torque so the gutter holds its line under a full load of water.
The situation: a 1950s Braeswood ranch whose gutters overflow at the inside corners in every heavy rain, with water staining on the fascia.
How we approach it: we measure the roof area feeding those corners, resize the gutter and add a downspout where the run demands it, and re-seal the corner joints — then water-test the system.
The situation: a Meyerland home whose gutters are pulling away from the fascia after years of heavy rain and debris load.
How we approach it: we check the fascia for rot, re-hang the gutter on hidden hangers at regular centres, and replace any section that is split or crushed rather than forcing it back into place.
The situation: A two-storey home in Kingwood whose downspouts dump water at the slab, with dampness showing at the foundation line under the pine canopy.
How we approach it: we extend the downspouts and redirect discharge away from the house, and check the gutter sizing above — a downspout can only carry what the gutter delivers.
Gutter problems start small and end at the fascia, the foundation or the roof deck. These are the ones we are called about most.
Ask a pro →We check the fascia for rot, replace damaged sections, and re-hang the gutter on hidden hangers at regular centres. A gutter screwed back into rotted fascia will pull away again.
Overflow at a corner usually means the gutter is undersized for the roof area feeding it, or the downspout is too far away. We resize the run or add a downspout — and check the roof valley above, which may be dumping more water than the gutter was sized for.
Sectional gutter leaks at its joints. We re-seal the seams where the gutter is sound, and recommend seamless replacement where the joints have failed across the run — a repair that lasts is better than a reseal that does not.
We extend downspouts and redirect discharge away from the house. Where the grade allows, water is carried clear of walkways as well as the slab.
“Absolutely wonderful service. Had an issue with my roof leaking and they were attentive and listened my concerns. They get on the roof and found and fix the leak then took care of the interior too. They even fixed a poorly done previous repair done by another company. I Would recommend”
Nate DorrGoogle review · 3 months ago
✓ Google review“I had completely roofing done on my house, Manny and his crew did great job! And they got the job done in a day then clean very good after all. Very happy!”
kim nguyenGoogle review · 6 months ago
✓ Google reviewThe reviews quoted on this page are word-for-word Google reviews of Bridgegate Construction LLC, shown with each reviewer's name as it appears on Google. We have read five of our 31 Google reviews — all 5 stars — and the rest appear only in that total. Read all 31 reviews on our Google profile.
As market context only — not a quote: Angi's Houston figures put seamless gutter installation at an average of $1,134, with most jobs between $887 and $1,380, and general gutter installation at an average of $927. Per linear foot, figures run roughly $3 to $25 depending on material — aluminium roughly $3.90 to $8.90, copper $14.80 to $24.70. Your price depends on the length, the size and the number of downspouts, and we quote it in writing after measuring your roofline.
It depends on the roof area each run must drain. Five-inch gutters suit smaller roof planes; six-inch gutters suit large or steep planes that shed a lot of water fast in a Gulf downpour. We size by roof area, not by habit, and add downspouts where the run demands it.
We do both. Gutter repair — re-hanging a run that is pulling away, re-sealing leaking seams, replacing a crushed downspout, clearing a blockage — is part of this service. We will tell you honestly when a repair will last and when the gutter has reached the point where seamless replacement is the better spend.
No — the City of Houston does not require a permit for gutter installation or replacement, unless structural changes to the roof are made, in which case a permit may be needed. Gutters are also a natural add-on to a roof replacement: if your roof is being replaced, that is the time to size and replace the gutters with it.
Call (346) 654-5170 and we will measure your roofline, price the runs and downspouts, and give you a written estimate. Gutter work from a local Houston crew — no pressure, no surprise line items.
Schedule an inspection — (346) 654-5170 →Call (346) 654-5170 or send us a message and we will get back to you during office hours. Tell us what is happening with your gutters or your roof and we will tell you what it takes to fix it. Office hours: Mon–Wed 8 AM–6:30 PM · Sat 9 AM–6:30 PM · Sun Closed.